Bryansk, Bryansk, Russian Federation
employee
Bryansk, Bryansk, Russian Federation
Development and experimental check of the algorithm and the program for automated technological providing of normal static contact rigidity of polished surfaces of machine parts and their joints at a stage of design-technology preparation of manufacture was considered.
normal static contact rigidity, automated technological providing, polishing, machine parts, preparation of manufacture.
1. MP 42-82. Method for determining normal contact rigidity of fixed joints. Manual. – M.: VNIIMASH, 1982.
2. Bishutin, S.G. Introduction of the required set of quality parameters of surface layers of parts when grinding: Monograph / S.G. Bishutin. – M.: Mechanical engineering-1, 2004. – 143 p.
3. Manual for machine tool designer / V. I. Kalinin, V. N. Nikiforov, N. Ya. Anikeev [etc.]. – M.: Mechanical engineering, 1983. – 288 p.
4. Surface engineering of parts / A.G. Suslov [etc.]; under the editorship of A.G. Suslov. – M.: Mechanical engineering, 2009. – 320 p.
5. Reference Book of steel and and alloy / under the editorship of A.S. Zubchenko. – 2-d Edition, revised and supplemented – M.: Mechanical engineering, 2003. – 782 p.
6. Medvedev, D. M. Single-stage technological support of wear resistance of cylindrical surfaces of machine components while machining / D. M. Medvedev // Bulletin of Bryansk State Technical University. – 2010. – No. 2. – pp. 4-9.
7. Reference Book for toolmaker / I.A. Orderlies [etc.]; under the general edition of I.A. Ordinartsev. – L.: Mechanical engineering, 1987. – 845 p.
8. Suslov, A.G. Automation of calculation for normal contact joint rigidity of flat surfaces of polished parts / A.G. Suslov, S.G. Bishutin, D. M. Medvedev, V.A. Handozhko//Bulletin of Bryansk State Technical University. – 2006. – No. 2. – pp. 135-139.
9. Suslov, A.G. Principles of mechanical engineering / A.G. Suslov, A.M. Dalsky. – M.: Mechanical engineering, 2002. – 684 p.
10. Suslov, A.G. Single-stage technological support of wear resistance of cylindrical surfaces of machine components / A.G. Suslov, D. M. Medvedev//STIN. – 2010. – No. 8. – pp. 22-25.
11. Suslov, A.G. Technological increase of friction surface durability of machine parts on the basis of power approach / A.G. Suslov, D. M. Medvedev, A.N. Shoyev//Friction and lubrication in machines and mechanisms. – 2011. – No. 6. – pp. 46-48.
12. Suslov, A.G. Power approach to the technological support of wear resistance of friction surfaces of machine parts / A.G. Suslov, D. M. Medvedev, A.N. Shoyev//Bulletin of mechanical engineering. – 2011. – No. 10. – pp. 56-58.
13. Handozhko, VA. Modernization of the scientific research automated system of contact rigidity on the basis of the advanced normalized test procedure / VA. Handozhko // Bulletin of Bryansk State Technical University. – 2006. – No. 2. – pp. 145-147.
14. Handozhko, VA. Single-stage technological support of wear resistance of cylindrical surfaces of machine components: Thesis for… Can.Eng.Degree / V.A. Handozhko. – Bryansk, 2007. – 20 p.
15. Hudobin, L.V. Lubricant cooling liquids in case of abrasive and diamond processing / L.V. Hudobin. – M.: Mechanical engineering, 1977. – 55 p.
16. Bezjyazychniy, V. F. Calculated determination of the technological processing conditions providing the given contact rigidness of the conjugated surfaces / V. F. Bezjyazychniy // Reference Book. Engineering journal. Annex. – 2014. - No. 8. – pp. 9-15.
17. Progressive instruments and grinding technologies: Collective Monograph / under the editorship of A.V. Kirichek. – M.: Publishing House SPECTR, 2013. – 320 p.
