employee
Bryansk, Bryansk, Russian Federation
Bryansk, Bryansk, Russian Federation
employee
Bryansk, Bryansk, Russian Federation
graduate student
Bryansk, Bryansk, Russian Federation
UDK 621.78 Нагрев. Термообработка. Упрочнение в холодном состоянии
A comparative analysis of samples porosity, synthesized from powder and wire is given. A higher efficiency of wire additive technologies, the implementation of which results in a significantly smaller pore size with reduced volume occupied by them, is shown. It is concluded that the use of layer-wise compaction or periodic undular strainer-hardening allows for achieving, at least 2 times, size loss of pores and 3 times reduction in the number of them, compared to the synthesis of wire products using the same method in similar most rational modes.
additive technologies, synthesis, powder, wire, porosity, hardening, deformation wave
1. Kalaida, T.A. The method of selective laser melting for the creation of products with complex geometry, Proceedings of the XV Russian annual conference of young researchers and postgraduates «Physico-chemistry and technology of inorganic materials», Moscow, 2018, pp. 55-56.
2. Features of materials and technologies of additive manufacturing of products / A.N. Kubanova, A.N. Sergeev et al./ Chebyshevsky collection, 2019, vol. 20, issue 3, pp. 453-477
3. Zlenko M.A., Nagaytsev M.V., Dovbysh V.M. Additive technologies in mechanical engineering. Moscow, SSC RF FSUE «NAMI», 2015, 220 p. (In Russian).
4. Gibson, Ya., Rosen, D., Stacker, B. Technologies of ad-ditive manufacturing. Translated from English / Edited by I.V. Shishkovsky. Moscow.: Technosphere, 2016, 656 p.
5. Ageeva, E.V. Altukhov, A.Yu., Sysoev, A.A., Osminina A.S. Investigation of porosity of sintered specimen from electroerosive cobalt-chromium powders / Izvestiya Yugo-Zapadnogo gosudarstvennogo universiteta, 2017, vol.21, no.6 (75), pp. 51-59.
6. Oglezneva, S.A. Structure and properties of steel PK100X2N (analog SHX15) [Electronic resource] // Bernstein readings dedicated to the 85th anniversary of the birth of Prof. Bernstein M.L, 2004, 64 p. URL:http://tmo.misis.ru/docs/thesis2004.pdf (accessed 07.04.2020).
7. Oskolkov, A.A., Matveev, E.V., Bezukladnikov, I.I., Trushnikov, D.N., Krotova, E.L. Advanced technologies for additive manufacturing of metal product. Bulletin PNRPU. Mechanical engineering, materials science, 2018, vol. 20, no. 3, pp. 90-105. Doi: 10.15593/2224-9877/2018.3.11.
8. US 20070122560 (A1). Solid-free-form fabrication process including in-process component deformation. Robbie J. Adams, Phoenix, AZ. 2007.
9. Haselhuhn, A.S. Design for Low-Cost Gas Metal Arc Weld-Based Aluminum 3-D Printing, Michigan Technological University, 2016.
10. Antonysamy, A.A. Microstructure, Texture and Me-chanical Property Evolution During Additive Manufacturing Of Ti6Al4V Alloy for Aerospace Applications, The University of Manchester, 2012
11. Stavinoha, J.N. Investigation of Plasma Arc Welding as a Method for the Additive Manufacturing of Ti-6Al-4V Alloy Components, Montana Tech of The University of Montana, 2012.
12. Malcolm Dinovitzer, Xiaohu Chen, Jeremy Laliberte, Xiao Huang, Hanspeter Frei Effect of wire and arc additive manufacturing (WAAM) process parameters on bead geometry and microstructure // Additive Manufacturing. – 2019. – Vol. 26. – PP. 138-146.
13. Kirichek, A.V., Sergeev, A.G., Fedonina, S.O. Tech-nological environment effect on the quality of parts synthe-sized by the 3DMP method. Structural materials life cycle (from receipt to recovery). Proc. of XI all-Russian sci.-tech. conf. with international participation / Edited by S.A. Zaides. Irkutsk: IRNTU Publishing House, 2021, pp. 4-8.
14. Possibilities of additive-subtractive-strengthening tech-nology / A.V. Kirichek, D.L. Soloviev et al. Bulletin of the Bryansk State Technical University, 2016, no.4 (52), pp. 151-160.
15. Additive-subtractive technologies – an effective ap-proach to innovative production / A.V. Kirichek, O.N. Fedonin et al. Bulletin of the Bryansk State Technical University, 2019, no.8 (81), pp. 4-10
16. Kirichek, A.V., Soloviev, D.L., Fedonina, S.O. Manifestation of technological heredity in the study of hardness of deformation-thermally hardened steels / Science intensive technologies in mechanical engineering, 2019, no. 8 (98). pp. 25-28.
17. Shchitsyn, Yu.D., Terentyev, S.A., Neulybin, S.D., Ar-temov, A.O., Belyanin D.S. Structuring and developing prop-erties of steel 04X18N9 in additive work-piece manufacturing. Bulletin of PNRPU. Mechanical engineering, materials science, 2018, no. 3, vol. 20, pp. 55-62.
